birthclutch2

Reasons Your Fiat 500 Key Fob Won't Work A key fob with the fiat 500 number is a convenient way to unlock the doors and get started the car. There are a myriad of reasons the fob won't work. These include a dead coin battery water damage, receiver module issues, and interfering. This listing is for an NEW replacement Fiat Flip Key Remote – like the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). Includes lock, unlock and trunk buttons. Dead Coin Battery A dead battery is the most frequent reason for your 500 key fob being inoperative. fiat key The Key Lab operate with a limited operating range and should be within just a few feet of the car to operate. If you're not close to your vehicle and press the key fob button, the car won't be able to respond, and will display the “Key Fob Not Detected” message in the instrument cluster. If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery of a reputable brand like Panasonic Duracell or Energizer. They can be found in your local hardware store, or on the internet. You can test the battery in the coin-cell by pressing the buttons while you are standing close to your Fiat 500. The parking lights will flash and the key fob will operate the lock and unlock switches. If the key fob won't work after replacing the battery, it may have water damage that stops it from communicating with the receiver module inside your vehicle. Water damage can occur through a variety of methods, including a simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this doesn't work your fob will probably require reprogramming by an experienced auto locksmith or the dealer. Water Damage While the fob comes with rubber seals that keep water from the chip's electronic circuit it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob's circuit board and can cause it to short out and eventually end up dying. The fob getting wet is not an ideal choice however, if you drop it in a glass of water or forget to take it out of your pants pocket prior to running the washer and you don't have a chance, don't give in. First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Check the fob to verify if it's working. If the fob doesn't work, it may need to be reprogrammed. This is typically done by a dealer or professional auto locksmith. If your key is old and is not programmed for your vehicle, you will need to replace it completely. A professional locksmith in the automotive industry can carry out this simple task. The locksmith will require the key cut to match your car's ignition. They'll also need to reprogram the fob in your car's system. This is an affordable and quick process that can be completed on the same day. Receiver Module Issues One of the most common reasons why your 500 key fob may stop working is because it's out of range. The remote usually has an operating range of 30 feet or less and if it's far from your car, it won't respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds. If you've replaced the battery in your coin (commonly known as”button” or “button” or “watch”) and the fob won't work it could be due to an internal circuit board problem. In most cases, reprogramming the fob will fix the issue. You can find directions on how to do this for most automobiles by searching YouTube or checking out the owner's manual. It's possible that you need to replace the metal retaining clips that keep the coin battery in place. If they loose tension, it may prevent your battery from being properly seated, causing your remote to malfunction. In rare instances, the fob may be out of sync with your vehicle because due to hardware or software issues. This could be a huge issue, but you are able to usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances they may have to reinstall the software on your body control module as well. Interference Interference can also cause the key fob to not be able to receive or transmit an signal. This could occur if the key fob is close to an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. The key fob may not work due to a bad connection with the buttons water damage or damage to the internal chips. If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets. There's a quick and easy way to reset the 500's onboard system including the keyfob. Disconnect the battery of 12 volts for about 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will clear out any remaining electricity and restart the car's computer system, which can help the key fob to function again. If the issue persists, you should speak with an expert technician. They'll be able determine the root of your problems.